Fraunhofer completes recyclable food packaging film trials

Fraunhofer completes recyclable food packaging film trials

German researchers complete trials of recyclable protective food packaging films. Fraunhofer’s MOBILE project combines predominantly single-polymer structures with functional barrier coatings and recycled content, demonstrating mechanical recycling while identifying remaining surface-quality limitations.


IN Brief:

  • Fraunhofer ISC's completed MOBILE project produced packaging films containing at least 95% of one base polymer.
  • The materials use polyolefin films incorporating up to 45% recycled content, combined with thin protective barrier coatings.
  • Industrial demonstrators were recycled into new film, although surface imperfections affected the quality of the recovered material.

German researchers have completed trials of recyclable food packaging films that combine predominantly single-polymer structures with thin protective coatings, demonstrating a potential route towards flexible packaging that retains barrier performance while supporting mechanical recycling.

The completed MOBILE project was coordinated by the Fraunhofer Institute for Silicate Research ISC and involved industrial packaging manufacturers, coating specialists and research organisations. Its results, published on 17 November, include packaging manufacture, filling trials, recycling and the production of new film from recovered material.

The project developed films containing at least 95% of a single base polymer. Researchers incorporated up to 45% recycled material into the polyolefin films used in the trials and applied functional coatings intended to provide the necessary protection against the movement of gases and moisture.

Flexible food packaging often combines several different polymers because individual materials provide different characteristics. One layer may support mechanical strength, another may enable reliable sealing, while a separate layer provides resistance to oxygen or water vapour.

These combinations can deliver useful packaging performance but complicate mechanical recycling. When incompatible polymers remain mixed during reprocessing, the resulting material may exhibit inconsistent mechanical or optical characteristics, limiting its suitability for subsequent manufacturing operations.

The MOBILE consortium sought to reduce that material complexity while preserving the properties required for food protection. It used predominantly single-polymer film structures and added thin barrier coatings rather than relying on substantial layers of several different polymers.

Fraunhofer ISC developed formulations based on its ORMOCER hybrid coating technology. These materials combine organic and inorganic components and can be adapted to provide functional properties when applied to polymer surfaces.

The coatings needed to remain compatible with the flexible base film while supporting the application of additional barrier layers. A coating that fractures or loses adhesion during film handling may undermine the packaging’s protective function, even where its initial laboratory measurements are satisfactory.

The researchers also investigated very thin inorganic barrier layers, including silicon oxide and aluminium oxide. These materials can reduce the transmission of particular gases or vapours when applied as continuous coatings under suitable processing conditions.

Film structure is important because barrier performance depends on more than the chemical composition of the coating. Defects, uneven thickness, damage during conversion and changes in the underlying surface can create pathways through which gases or moisture pass more readily.

The consortium applied its coatings to polyolefin films manufactured with recycled content and subsequently laminated them with compatible sealing layers. This produced structures intended to meet packaging requirements while retaining a high proportion of one base polymer.

The resulting material was tested through practical packaging operations. Project partners Etimex, Constantia and Leeb manufactured tubular-bottom bags, which Töpfer Babywelt subsequently filled. Fraunhofer’s Institute for Process Engineering and Packaging IVV then recycled the completed demonstrators.

The recovered material was processed into new film, allowing the researchers to assess the effect of recycling on subsequent material properties. This extended the work beyond an assessment based solely on polymer composition or the theoretical compatibility of the packaging structure with recycling equipment.

Mechanical testing indicated that the recycled material retained broadly comparable properties. The results support the feasibility of recovering the material and processing it into another film, although they do not establish that repeated recycling will preserve every characteristic indefinitely.

The researchers also observed minor surface imperfections, including speckles and pinholes. Speckles were associated with small impurities, while the pinholes appeared as small crater-like depressions in the surface.

These defects can influence appearance and may also affect barrier performance. The presence of imperfections demonstrates that successful mechanical recycling does not necessarily produce a film identical to the original material in every respect.

The distinction becomes important when recycled films are intended for applications requiring consistent protection against oxygen or moisture. A material may retain adequate tensile properties while displaying local defects that influence permeation performance or finished-pack appearance.

Fraunhofer IVV assessed material properties, recyclability, permeation behaviour and food safety considerations during the project. The work provides a basis for further evaluation of the packaging structures, but the results should not be interpreted as unrestricted regulatory clearance for all food-contact uses of the recycled films.

The suitability of recycled plastic for food contact depends on the materials involved, their source and processing history, and the applicable regulatory framework. Commercial packaging manufacturers would still need to establish compliance for their intended structures and production arrangements.

The project also included an environmental life cycle assessment conducted with reference to DIN EN ISO 14040 and DIN EN ISO 14044. These standards provide a framework for examining environmental impacts across the defined life cycle of a product system.

According to the consortium, the developed films performed better than conventional comparison structures in the environmental assessment. The reported findings support the potential value of reducing material complexity, although the results do not establish one universal environmental improvement applicable to every packaging format.

Material selection, energy consumption, conversion processes and end-of-life arrangements can all influence the outcome of such comparisons. A structure that performs favourably under one collection and recycling scenario may produce different results where the available infrastructure or recovered material quality differs.

The project was supported by the German Federal Ministry of Agriculture, Food and Regional Identity. Participating companies contributed specialist knowledge covering polymer films, coating technology, lamination and packaging manufacture, while the research organisations assessed material performance and recycling.

The work also coincides with the progressive application of the EU Packaging and Packaging Waste Regulation, which began applying on 12 August 2026. Its requirements are increasing the emphasis placed on packaging design, recyclability and the management of recovered materials.

Commercial implementation will require further work on coating consistency, material contamination and the quality of recycled film. Packaging suppliers will also need to establish reliable performance during forming, filling, sealing and distribution under the conditions required by individual food products.

The MOBILE trials demonstrate that predominantly single-polymer packaging can be manufactured with functional barrier coatings and returned to film production through mechanical recycling. The next development challenge is to control the surface defects identified in the recovered material while maintaining the required barrier and manufacturing performance.


Stories for you


  • Fraunhofer completes recyclable food packaging film trials

    Fraunhofer completes recyclable food packaging film trials

    German researchers complete trials of recyclable protective food packaging films. Fraunhofer’s MOBILE project combines predominantly single-polymer structures with functional barrier coatings and recycled content, demonstrating mechanical recycling while identifying remaining surface-quality limitations.


  • EU expands authorised food-contact plastics substances list

    EU expands authorised food-contact plastics substances list

    Four additional substances enter Europe’s authorised food contact plastics list. The approvals cover reinforced PEEK, a mineral filler, a PLA additive, and polyamide manufacture, with restrictions governing composition, migration, and intended applications.